Tube - Round - INFINITubeV - High Modulus - Plain Weave - Size 04 - 0.750 X 0.856 X 30 Inch
Estimated lead time for quantities greater than what is Available Now is expected to be between 2 and 4 weeks.
Single Telescoping Tube - INFINITubeV - Build Your Own Set
Engineered tubing to the rescue! Use for making quickly deploy-able tripod assemblies, boom poles, and virtually anything else telescoping!
The Standard Modulus Benefits include;
- Huge diameter range - 0.25" to 2.625" so you can hop on or off anywhere in the spectrum
- Use UHMW low friction tape to maintain snug fit & a cello wrap gloss finish
- Use the same tape above to prevent tubes from pulling apart at full extension
- All tubes (part #'s 464xx) in INFINITubeV have an ultra thin woven fiberglass inner layer to maintain superior machine-ability for hole drilling (if using button clips or locking pins) or slot cutting
- Great for machining - Fabric inner and outer plies minimize "breakout" typically associated with drilling into composites
You may also need
Features & Benefits
Fabric roll wrapped tubing offers many benefits over uni-directional and even filament wound tubing. That isn't to say it is the best however. Here are a few reasons you may wish to consider fabric roll wrapped tubing for your application.
- Superior machine ability
- Much better durability by reducing the potential extent of fiber breakout if drilled, machined or damaged
- Typical aesthetic associated with carbon fiber products
- Most "fabric" tubes contain a majority 0° plies in the layup allowing for the most effective bending load support. (whereas filament wound tubes cannot achieve angles less than ~7°
Additional Information
| Application | Telescoping |
|---|---|
| Telescoping Tube Family | INFINITubeV - Design Your Own |
| Materials | High Modulus Carbon |
| Pattern | 1k Plain Weave |
| Color | Black |
| Finish | Cello Wrap Gloss |
| Inside Diameter | 0.75 |
| Outside Diameter | 0.856 |
| Wall Thickness | 0.053 |
| Length | 30 |
| Length (max continuous) | 30.0 |
| Linear Density | 0.091 |
| Volumetric Density | 0.057 |
| Weight | 0.229 |
| Primary Fiber | Toray M40J |
| Primary Resin / Hardener | Eporite EHM82 |
| HTS - Harmonized Tariff Code | 6815.13.0000 |
Engineering Properties
All laminate properties and mechanical calculations are based on Classical Lamination Theory and should be used as a reference only. Rock West Composites does not guarantee these properties or calculations.
| Avg EX Young's Modulus | 1.894E7 |
|---|---|
| Avg EY Young's Modulus | 7476000.0 |
| GXY Shear Modulus | 1163000.0 |
| X Tensile Yield Strength | 124200.0 |
| X Compressive Yield Strength | 103900.0 |
| Y Tensile Yield Strength | 42840.0 |
| Y Compressive Yield Strength | 49950.0 |
| XY Shear Strength | 10600.0 |
| CTEX | 4.89E-07 |
| CTEY | 2.44E-06 |
| Poisson's Ratio vXY | 0.044 |
| Poisson's Ratio vYX | 0.017 |
Note:
- "X" is along the length of a tube, rod, plate, or panel.
- "Y" is around the perimeter of a tube, perpendicular to the length of pultruded parts, or along the width of a plate or panel.
Layup Orientation
46404-HM-L30 Rev NC
| Ply # | Orientation (degrees) | Location |
|---|---|---|
| 1 | (0/90 120 E-Glass Scrim) | Inside |
| 2 | 90 | ↓ |
| 3 | 90 | |
| 4 | 0 | |
| 5 | 0 | |
| 6 | 0 | |
| 7 | 0 | |
| 8 | 0/90 | Outside |
- 0° fibers maximize bending stiffness and run along the length of the part. Consider bending a tube over your knee.
- 45° fibers maximize torsional stiffness and are typically plied together in an opposing manner, i.e. ±45°. Consider twisting a tube like a vehicle's driveshaft.
- 90° (or "hoop") fibers maximize crushing stiffness and generally assist in overall durability. Consider laying a tube on the ground and stepping on it.